Set up
Place the machine on a flat, stable and level surface with adequate clearance for airflow.
Whip-It! Support Center
Can Sealer Pro
User Guide
Everything you need to set up, operate, clean and maintain your Can Sealer Pro - plus compatible Whip-It! PET bottles, lid options, technical specifications and warranty resources.
Keep hands and fingers away from the sealing port.
Review safety →Contact may cause serious or permanent injury. Power off, unplug and allow the machine to cool before cleaning or inspection.
Start here
Seal a bottle in four steps
Set the machine on a flat, stable surface, connect power, position the filled bottle with its lid, and allow the automatic sealing cycle to finish before removing it.
Connect power
Connect the power cord to the machine and a grounded outlet with the correct rated voltage, then press the Start switch.
Position bottle & lid
Place the lid on the filled Whip-It! bottle and slide it into the sealing port until it contacts the microswitch.
Seal & remove
Wait until the bottle is fully capped and sealed before removing it from the machine.
At a glance
Technical specifications
Compact countertop dimensions with a 2-inch sealing diameter and compatibility with bottles up to 7.87 inches tall.
Size9 × 15.75 × 7 in
Weight15 lb
Rated voltage110V / 220V
Rated power10W
Sealing diameter2 in
Max bottle height7.87 in
Know your machine
Parts & controls
Front controls include the LED display, sealing port and LED light strip. The rear panel contains the power connection, Start switch, ON/OFF control and counter reset.
Can counter
The main screen shows the lifetime count for cans sealed. Use the reset button on the back of the machine to reset the daily count to zero.
Placement
Allow a minimum of 6 inches of clearance on all sides. Keep the machine away from heat sources and use it in a climate-controlled indoor location.
Power
Use a grounded outlet with the correct rated voltage. The manual instructs users not to operate the Can Sealer with an extension cord.
Made to fit
Compatible PET bottles & lids
For optimal sealing performance, the user manual specifies Whip-It! PET bottles and compatible lids. Using the wrong combination can affect the seal and lead to leakage.
8.5 fl oz (250 ml)AC-51-250-Bowl2.4 in H × 3.5 in W
8.5 fl oz (250 ml)AC-51-250-Slim3.6 in H × 2.6 in W
11 fl oz (330 ml)AC-51-330-Slim4.5 in H × 2.6 in W
13.5 fl oz (400 ml)AC-51-400-Slim5.4 in H × 2.6 in W
17 fl oz (500 ml)AC-51-500-Wide5.1 in H × 3 in W
17 fl oz (500 ml)AC-51-500-Slim6.6 in H × 2.6 in W
24 fl oz (700 ml)AC-51-700-Wide6.5 in H × 2.8 in W
Pull Tab
AC-51-Lid-Pull · 2-inch aluminum lid
Easy Peel
AC-51-Lid-Peel · 2-inch aluminum lid
Reusable
AC-51-Lid-Clear · clear reusable lid
Care & operation
Setup, cleaning & maintenance
Use these quick-reference sections for routine operation. The full manual remains the authoritative source for complete safety and maintenance instructions.
- Inspect the packaging for shipping damage.
- Unbox carefully and account for all included components.
- Place the Can Sealer on a stable, level surface near an electrical outlet.
- Maintain at least 6 inches of clearance on all sides for airflow, avoid adjacent heat sources, and use the unit in a climate-controlled room.
- Make sure the machine is empty, turned off, unplugged and cool.
- Wipe with a damp cloth and mild cleaning solution; use a non-abrasive sponge.
- Regularly clean the exterior and lower mold to prevent buildup.
- Wipe all faces of the cup and film sensors with a damp rag, then dry.
- Confirm all parts are clean, sanitized and completely dry before use.
- Turn off the machine and disconnect it from power.
- Complete the cleaning process described above.
- Wipe exterior surfaces with a clean, damp cloth.
- Dry all wiped areas with a clean towel to prevent moisture buildup.
- Turn off and disconnect the machine from power.
- Wait 30 minutes for the heating element to cool.
- Inspect the plug and cord for discoloration, burn marks, cuts or tears.
- Check the integrity of electrical cords and plug points.
If issues are detected, the manual directs users to contact a service provider for recommended actions or replacements.
- After cleaning, turn off and unplug the machine.
- Store it in a dry place, preferably covered, to protect it from dust and help maintain longevity.
Safety first
Important operating precautions
Read the entire user manual before setup, operation or cleaning. Keep all operational and safety labels visible and legible.
!
Never insert hands or fingers into the sealing port during use.
✓
Use a grounded outlet with the correct voltage and a dedicated electrical circuit. Do not use an extension cord.
✓
Provide adequate ventilation and do not operate the machine unattended.
✓
Turn off, unplug and allow the machine to cool completely before cleaning, inspection or moving.
✓
Indoor use only. Keep children away from the machine and its controls.
Warranty
1-Year Limited Equipment Replacement Warranty
For eligible U.S. purchases from an Authorized Dealer, the warranty covers manufacturing defects for one year from the original delivery date and applies to the original purchaser. Claims must be reported within 30 days of discovering the defect and within the applicable warranty period. Contact the dealer or location where the product was originally purchased and have the order number available.
Warranty summary only. Exclusions, geographic limits, return authorization requirements and all other terms are governed by the full written warranty.
Resources
Downloads
Keep the quick guide near the machine and refer to the full user manual for complete instructions, safety guidance and maintenance requirements.
Need help with your Can Sealer Pro?
Contact Whip-It! support for product assistance, or refer to your original Authorized Dealer for warranty claims.
